Weight limits
Truck Weight Limits by State: Gross and Axle
On the Interstate, the federal limits are 80,000 lb gross, 20,000 lb on a single axle and 34,000 lb on a tandem (23 CFR 658.17), and each state sets its own rules on top for other roads. The table below lists the gross, single axle and tandem limits, height and semitrailer length for all 50 states and D.C., and each state name links to its own page. Some states keep higher grandfathered limits.
Federal source: 23 CFR 658.17, Weight. State limits can differ, so check the state page before you roll.
29 of 51 state pages are fully verified. The rest show "Pending" for any figure we haven't confirmed against an official source yet.
| State | Gross | Single axle | Tandem | Height | Semitrailer | Status |
|---|---|---|---|---|---|---|
| Alabama | 80,000 lb | 20,000 lb | 34,000 lb | Pending | Pending | Pending |
| Alaska | Pending | Pending | Pending | Pending | Pending | Pending |
| Arizona | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 57 ft 6 in | Verified |
| Arkansas | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | Pending | Pending |
| California | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | 48 ft | Verified |
| Colorado | 80,000 lb | 20,000 lb | 36,000 lb | 14 ft 6 in | No separate semitrailer length for a l… | Verified |
| Connecticut | 80,000 lb | 22,400 lb | 36,000 lb | Pending | Pending | Pending |
| Delaware | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 53 ft on Interstate, federal-aid prima… | Verified |
| District of Columbia | Pending | Pending | Pending | Pending | Pending | Pending |
| Florida | 80,000 lb | Pending | Pending | 13 ft 6 in | 48 ft | Pending |
| Georgia | 80,000 lb | 20,340 lb | 34,000 lb | 13 ft 6 in | 53 ft | Verified |
| Hawaii | 80,000 lb | 22,500 lb | 34,000 lb | Pending | Pending | Pending |
| Idaho | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | 48 ft | Verified |
| Illinois | 80,000 lb | 20,000 lb | 34,000 lb | Pending | Pending | Pending |
| Indiana | 80,000 lb | 20,000 lb | 34,000 lb | Pending | Pending | Pending |
| Iowa | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 53 ft in a truck tractor-semitrailer c… | Verified |
| Kansas | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | 59 ft 6 in | Verified |
| Kentucky | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in on highways the Transportat… | 53 ft on designated highways | Verified |
| Louisiana | 80,000 lb | 20,000 lb | 34,000 lb | Pending | Pending | Pending |
| Maine | Pending | Pending | Pending | 13 ft 6 in | 48 ft on the Interstate and National N… | Pending |
| Maryland | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 48 ft | Verified |
| Massachusetts | 80,000 lb | 22,400 lb | 34,000 lb | 13 ft 6 in | 53 ft | Verified |
| Michigan | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 50 ft | Verified |
| Minnesota | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 48 ft | Verified |
| Mississippi | 80,000 lb | 20,000 lb | 34,000 lb | Pending | Pending | Pending |
| Missouri | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft on the Interstate and designated… | 53 ft | Verified |
| Montana | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | 53 ft | Verified |
| Nebraska | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft 6 in | 53 ft including load | Verified |
| Nevada | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | Pending | Pending |
| New Hampshire | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 53 ft | Verified |
| New Jersey | 80,000 lb | Pending | 34,000 lb | Pending | Pending | Pending |
| New Mexico | 86,400 lb | 21,600 lb | 34,200 lb | Pending | Pending | Pending |
| New York | 80,000 lb | 20,000 lb | 34,000 lb | Pending | Pending | Pending |
| North Carolina | 80,000 lb | 20,000 lb | 38,000 lb | 14 ft | 53 ft | Verified |
| North Dakota | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | 53 ft | Verified |
| Ohio | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 53 ft in a tractor-semitrailer combina… | Verified |
| Oklahoma | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | Pending | Pending |
| Oregon | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | Pending | Pending |
| Pennsylvania | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 53 ft | Verified |
| Rhode Island | 80,000 lb | 22,400 lb | Pending | 13 ft 6 in | 53 ft | Pending |
| South Carolina | 80,000 lb | 20,000 lb | 35,200 lb | 13 ft 6 in | 53 ft on the Interstate and designated… | Verified |
| South Dakota | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | 53 ft on the Interstate and state trun… | Verified |
| Tennessee | 80,000 lb | 20,000 lb | 34,000 lb | Pending | Pending | Pending |
| Texas | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | 59 ft | Verified |
| Utah | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | 53 ft | Verified |
| Vermont | 80,000 lb | Pending | Pending | 13 ft 6 in | 53 ft on the Interstate and qualifying… | Pending |
| Virginia | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 48 ft | Verified |
| Washington | 80,000 lb | 20,000 lb | 34,000 lb | 14 ft | 53 ft | Verified |
| West Virginia | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 48 ft on the National Network and desi… | Verified |
| Wisconsin | 80,000 lb | 20,000 lb | 34,000 lb | 13 ft 6 in | 53 ft if the kingpin to axle distance … | Verified |
| Wyoming | Pending | 20,000 lb | Pending | 14 ft | 60 ft in a truck-tractor semitrailer c… | Pending |
53-foot trailer length and kingpin rules by state
Weight is only part of what a state checks. Many states also set rules on trailer length and on the kingpin-to-rear-axle distance, which is the measure behind most bridge laws for 53 foot trailers. Federal rules set the base for trailer length on the main truck routes (23 CFR part 658), and each state sets its own kingpin limit and what it allows on other roads. These rules differ by state and they change, so check the state DOT before you run. The table below links to each state's own page. Haul Math does not list a number here that is not sourced.
| State | Kingpin to rear axle limit | Max trailer length | Source (state DOT link) |
|---|---|---|---|
| Alabama | See state DOT | See state DOT | State DOT |
| Alaska | See state DOT | See state DOT | State DOT |
| Arizona | See state DOT | 57 ft 6 in | State DOT, State law |
| Arkansas | See state DOT | See state DOT | State DOT |
| California | 40 ft (38 ft for a single axle) | 53 ft | State DOT, State law |
| Colorado | See state DOT | See state DOT | State DOT |
| Connecticut | See state DOT | See state DOT | State DOT |
| Delaware | See state DOT | 53 ft | State DOT, State law |
| District of Columbia | See state DOT | See state DOT | State DOT |
| Florida | 41 ft | 57 ft | State DOT, State law |
| Georgia | See state DOT | 53 ft | State DOT, State law |
| Hawaii | See state DOT | See state DOT | State DOT |
| Idaho | See state DOT | 53 ft | State DOT, State law |
| Illinois | See state DOT | See state DOT | State DOT |
| Indiana | See state DOT | See state DOT | State DOT |
| Iowa | See state DOT | 53 ft | State DOT, State law |
| Kansas | See state DOT | 59 ft 6 in | State DOT, State law |
| Kentucky | See state DOT | 53 ft | State DOT, State law |
| Louisiana | See state DOT | See state DOT | State DOT |
| Maine | 45 ft 6 in | 53 ft | State DOT, State law |
| Maryland | See state DOT | 48 ft | State DOT, State law |
| Massachusetts | See state DOT | 53 ft | State DOT, State law |
| Michigan | See state DOT | 53 ft | State DOT, State law |
| Minnesota | 43 ft | 53 ft | State DOT, State law |
| Mississippi | See state DOT | See state DOT | State DOT |
| Missouri | See state DOT | 53 ft | State DOT, State law |
| Montana | See state DOT | 53 ft | State DOT, State law |
| Nebraska | See state DOT | 53 ft | State DOT, State law |
| Nevada | See state DOT | See state DOT | State DOT |
| New Hampshire | 41 ft | 53 ft | State DOT, State law |
| New Jersey | See state DOT | See state DOT | State DOT |
| New Mexico | See state DOT | See state DOT | State DOT |
| New York | See state DOT | See state DOT | State DOT |
| North Carolina | See state DOT | 53 ft | State DOT, State law |
| North Dakota | See state DOT | 53 ft | State DOT, State law |
| Ohio | See state DOT | 53 ft | State DOT, State law |
| Oklahoma | See state DOT | See state DOT | State DOT |
| Oregon | See state DOT | See state DOT | State DOT |
| Pennsylvania | 41 ft | 53 ft | State DOT, State law |
| Rhode Island | 41 ft | 53 ft | State DOT, State law |
| South Carolina | 41 ft | 53 ft | State DOT, State law |
| South Dakota | See state DOT | 53 ft | State DOT, State law |
| Tennessee | See state DOT | See state DOT | State DOT |
| Texas | See state DOT | 59 ft | State DOT, State law |
| Utah | See state DOT | 53 ft | State DOT, State law |
| Vermont | See state DOT | 53 ft | State DOT, State law |
| Virginia | 41 ft | 53 ft | State DOT, State law |
| Washington | See state DOT | 53 ft | State DOT, State law |
| West Virginia | See state DOT | 53 ft | State DOT, State law |
| Wisconsin | 43 ft | 53 ft | State DOT, State law |
| Wyoming | See state DOT | 60 ft | State DOT, State law |
Max trailer length is the longest semitrailer the state's own law allows, often on the Interstate and designated routes only. Open a state page for the full rule. Sources: FHWA and each state DOT, linked in the table. Check the official source before you run.
What is the kingpin rule for a 53 foot trailer?
Many states limit the distance from the kingpin to the rear axle. The limit is set by each state, so look up the state you run in using the table above and check the state DOT.
How to read these limits
- Interstate weights are the federal limits in 23 CFR 658.17 unless the state has grandfather rights, which each state page explains. Off the Interstate, states set their own weight limits.
- The bridge formula can hold you under 80,000 lb if your axles are close together. Check your rig with the bridge formula calculator.
- Width is 102 inches on the National Network in every state except Hawaii (108 inches).
- Height has no federal limit. FHWA notes most state limits range from 13 ft 6 in to 14 ft, with lower clearances on particular roads (Federal Size Regulations for Commercial Motor Vehicles).
- Semitrailer length is set by each state, often with a kingpin-to-rear-axle rule for 53-ft trailers. For kingpin-to-rear-axle and trailer length rules on a 53 ft trailer, see bridge laws for 53 foot trailers.
Check your state DOT before you load. The table is a planning tool and states change their rules.
Truck weight limits: the federal numbers and how the bridge formula works
On the Interstate, the federal limit is 80,000 lb gross, 20,000 lb on a single axle and 34,000 lb on a tandem, and the bridge formula can cap you lower than 80,000 if your axles are close together. Those limits come from 23 CFR 658.17. States can keep higher grandfathered limits, and they set their own rules off the Interstate.
Last updated: October 19, 2026
Haul Math is a free set of trucking calculators for owner-operators and small fleets, run by Hive Asset Group, LLC.
This is general information from official sources, not legal advice. Confirm with the state before you run.
The federal limits at a glance
| Limit | Federal number | Where it comes from |
|---|---|---|
| Gross vehicle weight | 80,000 lb | 23 CFR 658.17(b) |
| Single axle | 20,000 lb | 23 CFR 658.17(c) |
| Tandem axles | 34,000 lb | 23 CFR 658.17(d) |
| Axle groups of two or more | Bridge formula | 23 CFR 658.17(e) |
| Two tandem sets 36 ft or more apart (first to last axle) | 34,000 lb each | 23 CFR 658.17(e) |
The same rule says the 80,000 lb gross is the top, "except where lower gross vehicle weight is dictated by the bridge formula." It also says these weights include all tolerances, with a small allowance for portable scales. Source: https://www.ecfr.gov/current/title-23/chapter-I/subchapter-G/part-658/section-658.17
These federal rules apply to the Interstate and reasonable access to it (658.17(a)). Other roads follow the state's own limits.
The bridge formula in plain words
The axle limits tell you what one axle or one tandem can carry. The bridge formula looks at a longer stretch. It says the more axles you have, and the farther apart they are, the more weight the group can carry. Squeeze the axles together and the allowed weight drops.
W = 500 × (L × N ÷ (N − 1) + 12 × N + 36)
- W is the most weight, in pounds, the group may carry. The federal table rounds it to the nearest 500 lb.
- L is the distance in feet from the first axle to the last axle of the group.
- N is the number of axles in the group.
It applies to every group of two or more consecutive axles. The one that trips up most five-axle rigs is the whole truck, first axle to last. Our bridge formula guide walks through FHWA's own examples, and the bridge formula calculator checks every group on your rig.
Example: a 5-axle rig with the axles close together
Example only. Made-up spacing to show the math. Measure your own truck.
A 5-axle tractor-trailer has 40 feet from the first axle to the last.
- N = 5, L = 40
- 40 × 5 ÷ 4 = 50
- 12 × 5 = 60
- 50 + 60 + 36 = 146
- W = 500 × 146 = 73,000 lb
So this rig tops out at 73,000 lb, not 80,000. If the scale ticket reads 78,000 lb, that is 5,000 lb over for the whole truck, even though 78,000 is under the 80,000 gross.
Spread the same five axles farther and the number climbs. FHWA's five-axle example, with 51 feet from the first axle to the last, works out to 79,875, which rounds to 80,000 lb. That is on our bridge formula guide.
Gross, axle and tandem limits for a few states
Most states list the federal numbers for the Interstate. These states have a different axle number on our state table, and each one is marked verified there as of September 28, 2026:
| State | Single axle | Tandem | Our state page |
|---|---|---|---|
| Colorado | 20,000 lb | 36,000 lb | Colorado |
| Georgia | 20,340 lb | 34,000 lb | Georgia |
| Massachusetts | 22,400 lb | 34,000 lb | Massachusetts |
| North Carolina | 20,000 lb | 38,000 lb | North Carolina |
| South Carolina | 20,000 lb | 35,200 lb | South Carolina |
All five show 80,000 lb gross. For the rest, open the state page: Texas, California, Ohio, Pennsylvania and Arizona are good places to start, and the full list is in the table above on this page. A state page shows where its numbers came from. Where a figure says "Pending," we have not confirmed it yet.
Federal source for the grandfather rule: 23 CFR 658.17(i) says the single, tandem and gross limits do not apply to weights legally authorized under state law on July 1, 1956, and the group-of-axles rule does not apply to vehicles legally grandfathered under state tables on January 4, 1975. That is why a few states differ.
Permits and heavier loads
States may issue special permits that go past the axle, gross or bridge limits for nondivisible vehicles or loads (23 CFR 658.17(h)). If your load is one of those, ask the state permit office. Do not guess.
Before you load: a short check
- Know your axle spacing, first axle to last, in feet.
- Run the bridge formula for the whole truck and each group.
- Weigh on a certified scale and compare to the formula number, not just 80,000.
- Look up the state page for each state on the route.
- Confirm with the state before you run.
What an overweight load can cost you
Penalties are set by each state, and we do not list them here. Check the state DOT. For your own budget, price the weight in: the revenue on a load only counts if you can legally haul it, so run the rate through the load profit calculator or your cost per mile.
FAQ
What is the weight limit for a semi truck?
On the Interstate, the federal gross limit is 80,000 lb, with 20,000 lb on a single axle and 34,000 lb on a tandem (23 CFR 658.17). The bridge formula can lower the allowed weight if your axles are close together. States set their own limits off the Interstate.
Is 80,000 lb the same in every state?
The federal Interstate gross limit is 80,000 lb. Some states keep higher grandfathered limits, and many have different axle numbers. Check the state page and the state DOT.
What is the bridge formula?
It is a federal formula, W = 500 × (L × N ÷ (N − 1) + 12 × N + 36), that limits the weight on any group of two or more axles by their spacing and count. A five-axle truck with 40 feet between the first and last axle works out to 73,000 lb in our example.
Do I need a permit to go over 80,000 lb?
Federal rules let states issue special permits for nondivisible vehicles or loads that exceed the axle, gross or bridge limits. Whether one is available depends on the state and the load, so ask the state.
Why can I be legal on gross weight and still get a ticket?
The gross limit is only one check. A single axle, a tandem or the whole truck under the bridge formula can be over even when the total is under 80,000 lb. Weigh each axle group.
Where do I look up my state's limit?
Use the state table above, then open the state page. If a figure shows "Pending," check the state DOT directly.
How do I check if my axle spacing passes the bridge formula?
Enter your axle spacing in the bridge formula calculator and compare the result with your scale ticket. It is for planning only, so confirm with your state DOT before you load.
Get your numbers on paper
Want your real cost per mile? Get the free cost-per-mile sheet.
Source: 23 CFR 658.17, Weight (eCFR) · Last verified Sep 28, 2026
Source: FHWA, Compilation of Existing State Truck Size and Weight Limit Laws · Effective Oct 1, 2012 · Last verified Sep 28, 2026

Free, no signup
Know your number before you take the load
26 free calculators, no signup. Want your loads and numbers saved? Try Pro free for 14 days, no card.
