Skip to content
Haul Math

Reference

Bridge Laws for 53 Foot Trailers by State (Kingpin to Rear Axle)

Last updated: . Haul Math (haulmath.co) is a free set of trucking calculators by Hive Asset Group, LLC.

Short answer

For a 53 foot trailer, the kingpin to rear axle (KPRA) limit in the states we checked runs from 38 to 43 feet, and the number changes by state. The chart below lists only the states where we opened the state's own law or DOT page, and check your state DOT before you load.

This page is a reference, not legal advice. Laws change and roads inside a state can have their own rules, so confirm with the state before you run it.

Kingpin to rear axle limit by state

KPRA is the length from the kingpin to the rear axle (or the middle of the rear tandem, depending on how the state words it). The rows below use the state's own wording. "Not verified yet, check the state DOT" means we have not opened a state source we trust for that row, so we are not guessing.

StateKPRA limitSource
TXnot verified yet, check the state DOT (the Texas length page we opened gives a 59 ft semitrailer length and says nothing on kingpin distance)State source
CA40 ft for a semitrailer with two or more axles, 38 ft for one axle. A city or county may set the limit as low as 38 ft on its own roadsState source
FL41 ft, from the kingpin to the center of the rear axle or rear group of axles (semitrailer over 48 ft, up to 57 ft)State source
GAnot verified yet, check the state DOTnone opened
ILnot verified yet, check the state DOTnone opened
OHnot verified yet, check the state DOT (the section we opened allows a 53 ft semitrailer and gives no kingpin figure)State source
PA41 ft, from the kingpin to the center line of the rear axle or rear axle group (trailer up to 53 ft)State source
TNnot verified yet, check the state DOTnone opened
NC41 ft, to the rearmost axle or the midpoint of a tandem, for a semitrailer over 48 ftState source
IN43 ft to the rearmost axle for a semitrailer longer than 48 ft 6 in on the state highway system. Other road types not checkedState source
MInot verified yet, check the state DOTnone opened
NJ41 ft, from the kingpin to the centerline of the rear axle or rear axle group, for a trailer over 48 ft and up to 53 ftState source
NY43 ft, from the kingpin to the centerline of the rear axle, for a semitrailer over 48 ft and up to 53 ft on qualifying and access highwaysState source
VA41 ft, to the rearmost axle or the midpoint of the rear tandem, for a semitrailer up to 53 ftState source
WAnot verified yet, check the state DOT (the section we opened caps the semitrailer at 53 ft and gives no kingpin figure)State source
MOnot verified yet, check the state DOT (the section we opened caps the semitrailer at 53 ft and gives no kingpin figure)State source
AZnot verified yet, check the state DOTnone opened
ALThe 41 ft kingpin limit in the Alabama code we opened applies to semitrailers over 53 1/2 ft. We found no KPRA figure there for a 53 ft trailer, so check the state DOTState source
KYnot verified yet, check the state DOTnone opened
ORnot verified yet, check the state DOT (the chapter we opened covers overall length and gives no kingpin figure)State source

8 of the 20 states have a KPRA figure from a state source (CA, FL, PA, NC, IN, NJ, NY, VA), and AL is a partial answer. The other 11 are marked not verified yet. A blank is not a "no limit". It only means we have not confirmed it.

The federal rule behind all this is 23 CFR 658. It sets a 48 foot minimum trailer length that states must allow, and lets states keep longer lengths they already allowed (called grandfathered lengths). Some of those come with a KPRA condition. For example, the federal list says California allows trailers up to 53 feet with a KPRA of 38 feet and Indiana allows them with 40 feet 6 inches. The state numbers above can differ from that list, so read the state row first.

For weight rules on the same trucks, see weight limits by state. To check axle weights for a real load, use the load calculator. More walkthroughs are in the guides.

What KPRA is, and how it differs from the bridge formula

People say "bridge laws" for two different things. The federal bridge formula limits weight based on how far apart your axles are. KPRA limits the length from the kingpin to the rear axle, and it exists to keep the turning path of a long trailer close to a shorter one. A load can pass one and fail the other. To check the weight side, use the bridge formula calculator.

How to measure kingpin to rear axle

  1. Park the rig straight on level ground, trailer pinned to the tractor.
  2. Find the center of the kingpin. It sits on the bottom of the trailer, under the front.
  3. Find the point the state measures to. That is the rearmost axle, the center of the rear axle group, or the midpoint between the two tandem axles. The wording is different in each state, so use the one in the row for your state.
  4. Run a tape from the kingpin center to that point, along the length of the trailer.
  5. Write the number down for each tandem position you plan to use.

Measure to the same point every time. Measuring to the wrong axle is the easy mistake on a tandem.

How to slide the tandems

Sliding the tandems forward shortens KPRA. Sliding them back makes it longer. The slide also shifts weight between your axles. Moving the tandems forward puts more of the load on the trailer tandems and less on your drives. Moving them back does the opposite.

Example (made up numbers): your tandems sit at a 43 ft KPRA and the state you are about to enter has a 41 ft limit. You need to move the tandems forward by 2 ft or more, then re-check your steer, drive, and trailer axle weights on a scale. Moving a load's weight around can fix a KPRA problem and cause an axle weight problem, so scale it after the slide.

FAQ

What is the kingpin to rear axle limit for a 53 foot trailer?

It depends on the state. In the states we verified it runs from 38 ft (a California one axle trailer) to 43 ft (Indiana state highways and New York). The most common figure we found is 41 ft (FL, PA, NC, NJ, VA). Find your state in the chart and check your state DOT before you load.

Do all states have a KPRA limit?

We cannot say for all 50. We only list states where we opened a source. Several states show a 53 ft length limit in their law and no KPRA figure on the page we opened, and we have marked those not verified yet instead of assuming there is no limit.

Is the KPRA limit the same on the interstate and on state roads?

Not always. California lets cities and counties set a lower limit on local roads, and Indiana's 43 ft figure is for the state highway system. The chart gives the main figure for each state. Read the source link for road type notes.

Does sliding the tandems change my axle weights?

Yes. Moving them forward loads the trailer tandems more and the drives less. Moving them back does the reverse. Scale the truck after you slide.

Is this page legal advice?

No. It is a reference for drivers. Laws and routes change, so confirm the limit with the state before you load.

Sources

Next step

Free: the cost per mile sheet.

The $19 workbook. An Excel file (.xlsx) with working formulas, plus a printable PDF. Get the workbook

Free, no signup

Know your number before you take the load

26 free calculators, no signup. Want your loads and numbers saved? Try Pro free for 14 days, no card.

Get the free cost-per-mile sheetStart the free Pro trial