Blog
How to Quote a Load by Phone in Under Two Minutes
Add your deadhead miles to the loaded miles, multiply by your cost per mile, add 25 to 35 percent, then divide by loaded miles. That is the number you say to the broker, and this post shows the whole call.
Add the deadhead miles to the loaded miles, multiply by your cost per mile, add your margin, then divide by the loaded miles. That one number is what you quote, and you can get it in under two minutes with a pencil and a phone calculator. Below is the checklist, a full worked example, and a script for when the broker comes in low.
Know two numbers before the phone rings
You can't do this math live if you're also figuring out your costs live. Write two numbers where you can see them from the driver's seat:
- Your all-in cost per mile (CPM). Monthly expenses divided by total miles driven, with deadhead miles counted in the miles. If you don't have this yet, here is how to work it out.
- Your margin. A common rule is CPM plus 25 to 35 percent for a profitable minimum rate. Pick one number inside that range and stick with it.
If you run a financed truck, your CPM is higher than a paid-off truck's. One cost guide shows about $1.56 a mile for a financed truck versus about $1.23 paid off, on 8,000 miles and $12,500 of expenses. The truck payment alone moves the number that much, so use your own figure, not someone else's.
The two-minute checklist: six steps, one number
Keep this open on your phone. Times are rough, but the whole thing is six taps on a calculator.
- Get the loaded miles (about 15 seconds). Ask the broker for the pickup, the drop and the miles they're paying on. If the miles look off, check which miles the broker pays on.
- Work out your deadhead (about 15 seconds). Miles from where the truck sits right now to the pickup.
- Add them for total miles (5 seconds). Deadhead plus loaded.
- Multiply total miles by your CPM (10 seconds). That's what the load costs you to run.
- Add your margin (10 seconds). Multiply the cost by 1.25 for a 25 percent margin, or 1.35 for 35.
- Divide by the loaded miles (10 seconds). The result is your minimum rate per loaded mile, which is the number brokers quote in.
That's the whole job. Everything after this is what to do with the answer.
Example: a 300-mile load with 60 miles of deadhead
Example: say your CPM is $1.56, you're 60 miles from the pickup, and the load is 300 miles.
| Step | Math | Result |
|---|---|---|
| Total miles | 60 + 300 | 360 |
| Cost to run it | 360 x $1.56 | $561.60 |
| Minimum pay at 25 percent | $561.60 x 1.25 | $702.00 |
| Minimum pay at 35 percent | $561.60 x 1.35 | $758.16 |
| Minimum loaded rate, 25 percent | $702.00 / 300 | $2.34 a mile |
| Minimum loaded rate, 35 percent | $758.16 / 300 | $2.53 a mile |
So your range to quote is about $2.34 to $2.53 a loaded mile. Open at the top, settle no lower than the bottom.
Now the broker says $2.10 a mile. That's $630 of pay ($2.10 x 300). Divide by all 360 miles and you get $1.75 a mile. It clears your $1.56 cost, but only by 19 cents a mile, about $68 on the whole load. That's under half of what a 25 percent margin would give you. Counter.
Deadhead changes the answer more than anything else
Same load, same broker, but the truck is 150 miles from the pickup instead of 60.
- Total miles: 150 + 300 = 450
- Cost to run it: 450 x $1.56 = $702.00
- Minimum pay at 25 percent: $702.00 x 1.25 = $877.50
- Minimum loaded rate: $877.50 / 300 = about $2.93 a mile
The load didn't change. The ask went up 59 cents a loaded mile because of 90 extra empty miles. This is the mistake that costs the most, and it's why the loaded rate alone never tells you anything. One rate-per-mile explainer shows it plainly: 120 loaded miles at $4.50 pays $540, but add 180 empty miles and the trip works out to $1.80 a mile.
When the pickup is far from where you are, the deadhead is what pulls your real rate down. Empty miles cost fuel and time whether or not there's freight on the trailer. So raise your ask or pass. For more on empty miles, see what deadhead really costs.
Decide in three seconds: take it, counter, or pass
Once you have your minimum, the call is a decision table.
| The broker's offer is... | Do this |
|---|---|
| At or above your 35 percent number | Take it, or ask for a little more. |
| Between your 25 and 35 percent numbers | Counter once, near the top of your range. |
| Below your 25 percent number | Counter once with your number. Don't go under it on the call. |
| Below your CPM times total miles | Pass. You'd be paying to haul it. |
| Delivery area is hard to get out of | Raise your number before you start. |
That last row comes from drivers who say they adjust rates up for known difficult areas and never down for an easy market.
Say your number first, with a reason attached
The first number on the table anchors the call. Brokers rarely lead with their highest rate, and accepting the first number is where many owner-operators lose money. One forum thread also points out that when a driver states a minimum per mile, the broker may agree fast, which can leave money on the table. So quote from the top of your range, not the bottom.
And go in with data. Know your cost per mile and current market trends, then use them to justify a higher rate. Your phone math is that data.
Paste this counter script
A template to adapt, not a transcript of a real call. It's adapted from a negotiation template:
"Appreciate the offer, but $[their number] is well under what this lane is running, and it doesn't cover my cost to get the truck there and back. If you've got room to get to $[your number], I'm ready to roll today. If not on this one, keep me in mind for [origin] freight. I run this lane often and I'd rather build something steady than haggle load by load."
Fill in $[your number] with the result from step 6. The deadhead and cost per mile from your math are the reason in the second sentence, and you can say that part out loud and mean it.
Four mistakes that cost you on the call
- Leaving deadhead out. Your quote comes out too low and the load looks fine until the settlement. This is the big one.
- Quoting from the bottom of your range. If the broker says yes in two seconds, you probably left money on the table.
- Getting heated or going quiet after a no. Emotional reactions and ghosting the broker both cost you future freight. Stay level and keep the door open.
- Using one flat per-mile number for every lane. Long deadhead and hard delivery areas need a higher number. A hard floor like not moving the truck under $2 a mile on 400-mile-plus hauls is one driver's rule in a forum thread, not a standard. Your floor comes from your CPM.
If the broker says that's the best they can do, here is what to say next.
Do this in the next ten minutes
Pick up a pen and write your CPM and your margin on a card, then stick the card to the dash. Run the six steps once on the last load you hauled, using its real deadhead and loaded miles. If the result is more than the load paid, you've just found out what that lane was worth.
Get the math without the pencil
The six steps are simple, but they're easy to fumble with a broker waiting and a load board refreshing. HaulMath runs this kind of freight math for owner-operators so you can see the number quickly. It's a calculation tool, not a replacement for an accountant. Try HaulMath on your next quote.
Common questions
- Do I count deadhead miles when I quote a load?
- Yes. Add the deadhead miles to the loaded miles to get total miles, multiply by your cost per mile, add your margin, then divide by loaded miles to get the rate you quote. Leaving deadhead out makes the quote too low.
- What is the difference between loaded rate per mile and total rate per mile?
- Loaded rate per mile is pay divided by loaded miles only. Total rate per mile is pay divided by loaded plus deadhead miles. Compare the total figure to your cost per mile to see whether a load really pays.
- How much margin should I add to my cost per mile?
- One cost guide uses 25 to 35 percent above cost per mile as a profitable minimum rate. Pick a number in that range, keep it steady, and use the top of it as your opening ask.
- Should I give my number first or let the broker go first?
- Give yours first when you have solid numbers behind it. Brokers rarely open with their highest rate, so the first number on the table tends to anchor the call. Quote from the top of your range and leave room to settle.
- What should I say when the broker's offer is too low?
- Acknowledge the offer, say it doesn't cover the cost of getting the truck there and back, give your number, and offer to keep them in mind for future freight on the lane. Stay calm and polite either way.
- How do I find my cost per mile if I don't know it yet?
- Divide your total monthly expenses by the total miles you drove that month, counting empty miles in the miles. Use a full month so fuel, insurance, maintenance and truck payments all show up.
Run your own numbers
Free calculators for owner-operators: load profit, cost per mile, IFTA, per diem, and more. Every answer shows the math.