Blog
How to Add Tolls and Scale Fees to Your Load Math
Tolls and scale fees come off the load pay before you compare it against your cost per mile. Here is the seven-step worksheet, a toll break-even rule and what to say to the broker.
Take the load pay, subtract fuel, tolls and scale fees, then divide what is left by every mile you drive for the load, loaded and empty. If that number beats your cost per mile, the load pays. The seven steps below take two minutes, and you can run them while the broker is still on the phone.
Tolls and scale fees belong to the trip, not to your yearly average. They come off the top first, and only then do you compare against your cost per mile. Bubba's load profitability guide defines net revenue per mile the same way: gross revenue minus tolls, fees and fuel, divided by loaded miles plus deadhead miles. A load is profitable when that figure is above your cost per mile.
Run these seven steps on every load
- Write down the load pay.
- Estimate fuel for loaded plus empty miles. The trip fuel guide shows how.
- Add the tolls for the exact route.
- Add the scale fees for the stops you expect.
- Subtract steps 2 to 4 from step 1.
- Divide by loaded miles plus deadhead miles.
- Compare the result to your cost per mile, with fuel, tolls and scale fees taken out of that baseline so nothing is counted twice.
Keep one list and use it once. If your cost per mile already includes tolls, take them out of the baseline or leave them out of the trip. Counting them in both places makes good freight look bad, and you turn it down.
A worked load: $2,400 pays, but what do you keep?
Example: say an 800-mile load pays $2,400, you run 100 empty miles to the pickup, fuel runs $0.80 a mile, you pay $85 in tolls and make two scale stops with one reweigh. Your cost per mile for everything else (truck note, insurance, maintenance, tires) is $1.20. Swap in your own figures and the table works the same way.
| Line | Amount |
|---|---|
| Load pay | $2,400.00 |
| Fuel, 900 miles at $0.80 | $720.00 |
| Tolls | $85.00 |
| Scales | $26.50 |
| Left after trip costs | $1,568.50 |
| Net per mile, $1,568.50 over 900 miles | about $1.74 |
| Your other costs | $1.20 a mile |
| Kept per mile | about $0.54 |
| Kept on the load | $488.50 |
Dividing by the 800 loaded miles alone would have shown about $1.96 and hidden the empty miles. Those 100 miles burned fuel and time. The deadhead miles guide covers that cost in detail, and the full profit check shows where this worksheet plugs in.
Price the toll for your axle count and how you pay
A toll is not one number. It depends on your axle count and on how you pay. The West Virginia Turnpike rate page lists a 5-axle truck at $15.00 cash or $12.00 with a commercial transponder.
Run that plaza both ways on a round trip and it is $24.00 with the transponder or $30.00 in cash. The $6.00 gap comes straight out of your margin. Bestpass says the same thing in general terms: tolls reduce your margin directly, and high-toll regions hit hardest.
Get the toll number before you answer the broker
- Count your axles the way the toll agency counts them, trailer included.
- Open each toll road's own rate chart or calculator. A car-only calculator skips the axle step.
- Pick the column that matches how you pay: commercial transponder or cash.
- Add every gate or section on the route, and the return trip if you come back on the same road.
- Write one total on the toll line, using this year's rates.
Count scale fees per load, not per mile
Scale fees are a per-load cost. Use this line:
Scale line = (weighs x first-weigh fee) + (reweighs x reweigh fee)
Land Line reported the CAT Scale first weigh at $12 and each reweigh at $2.50, up from $11.50 and $2. Check the posted price at the scale you use, since it moves. On the example load, two weighs and one reweigh is 2 x $12 + $2.50 = $26.50, about 1 percent of the pay.
Now the same line on a short haul. Example: say a $600 load, 250 loaded miles plus 50 empty, with three weighs and one reweigh. That is 3 x $12 + $2.50 = $38.50, which is about 6.4 percent of the pay and about 13 cents a mile. Same fee, a much bigger bite. When the load is short with several stops, count every scale stop you expect. If short hauls are your lane, read whether a short haul load is worth it next.
Pay the toll only when it saves more than it costs
When a toll road and a free road differ in miles, do not trust the first number. The toll is worth paying when it saves you more in mileage costs than the toll charges.
Break-even toll = miles saved x (fuel per mile + wear per mile)
Use the costs that rise with every mile: fuel, tires, maintenance. Leave out the truck note and insurance, because you owe those whether the truck rolls or not.
Example: the same $2,400 load. The toll route is 780 loaded miles with $85 in tolls. The free route is 840 loaded miles with no tolls. Both have 100 empty miles and $26.50 in scales. Fuel is $0.80 a mile and tires plus maintenance run $0.45 a mile.
| Toll route | Free route | |
|---|---|---|
| Total miles | 880 | 940 |
| Fuel at $0.80 | $704.00 | $752.00 |
| Tires and maintenance at $0.45 | $396.00 | $423.00 |
| Tolls | $85.00 | $0.00 |
| Scales | $26.50 | $26.50 |
| Left before fixed costs | $1,188.50 | $1,198.50 |
The toll route saves 60 miles, which is worth 60 x ($0.80 + $0.45) = $75. The toll costs $85, so it loses by $10. The free road wins on cash.
Here is the rule:
- Toll under the break-even number: take the toll road. It pays for itself.
- Toll over the break-even number by a few dollars: the free road wins on cash, but the toll road buys you time. Here $10 buys about an hour at 55 mph, so if you are tight on hours or the delivery window, pay it.
- Toll far over the break-even number: take the free road.
Fixed costs, like the note, are paid by the day. If the toll road gets you home a day sooner, count that day.
Who pays: read the rate confirmation, then ask
When the rate confirmation says who pays tolls or scale tickets, use that. When it is silent, ask before you accept, because the answer changes your number. If you are leased on, check your lease or carrier agreement for scale reimbursement before you put the fee on your cost list. If a broker agrees to cover tolls or scales, get it written on the rate confirmation. The rate confirmation checklist shows where to look.
Say this on the call or in the thread:
"I priced tolls and scales on that route at my axle count. Do you cover them on this one, or are they on me?"
If they are on you and you come up short, say it plainly:
"My rate covers fuel, tolls and scales for that route. At this number I am short. I can do it at [your number]."
Work out [your number] with one line: the dollars per mile you are short, times total miles. Short by 20 cents a mile on 900 miles? That is $180 more on the load, or you pass. To build the baseline you are comparing against, start with your cost per mile.
Five mistakes that quietly eat the load
- Leaving tolls out of the quote. Every toll dollar comes straight out of your margin on that load.
- Counting tolls or scales twice, once on the trip and once in your cost per mile. Good freight looks bad.
- Pricing for the wrong axle count or payment method. On the West Virginia example the gap is $3.00 a pass between cash and transponder for a 5-axle truck.
- Dividing by loaded miles only. The empty miles to the pickup still cost fuel and time.
- Assuming the broker pays. If the rate confirmation is silent, the fee may land on you. Ask first, then get it in writing.
Do this in the next ten minutes
Pull up the last load you took that crossed a toll road. Look up the toll for your axle count and payment method, count the scale stops, and run the seven steps. If the net per mile lands below your cost per mile, that lane needs a higher quote, or a pass.
Put the math in one place
Doing this by hand works, but it is a lot of steps to run while a broker waits on an answer. HaulMath does the freight math for you so you can see in seconds whether a load pays. Try HaulMath and run your next load through it before you say yes.
Common questions
- Do I subtract tolls before or after I work out rate per mile?
- Before. Subtract tolls, scale fees and fuel from the load pay first, then divide what is left by loaded plus empty miles, and compare that to your cost per mile.
- Are scale fees part of cost per mile or a per-load cost?
- Treat them as a per-load cost. Count the weighs and reweighs you expect on the trip and put one number on the scale line. If your yearly cost per mile already includes them, do not subtract them again.
- Do deadhead miles count when I divide?
- Yes. Divide by loaded miles plus empty miles, because the empty miles to the pickup still burn fuel and time.
- Who pays tolls, me or the broker?
- Whatever the rate confirmation says. If it is silent, ask before you accept, and get any agreement to cover tolls or scale tickets written on the rate confirmation.
- How do I know the toll cost for a route before I take the load?
- Use each toll road's own rate chart or calculator, pick your axle count and the column for how you pay, then add every gate on the route. Use this year's rates.
- When is a toll road worth paying?
- When the miles it saves times your fuel and wear cost per mile is more than the toll. If the toll is a few dollars over that number, pay it only when the time saved matters for your hours or the delivery window.
Run your own numbers
Free calculators for owner-operators: load profit, cost per mile, IFTA, per diem, and more. Every answer shows the math.